Con i nostri cookie, vorremmo offrirti la migliore esperienza di shopping possibile, con tutto ciò che ne consegue. Questo include, ad esempio, offerte adatte, annunci personalizzati e il salvataggio delle preferenze. Se per te va bene, acconsenti semplicemente all'uso dei cookie per preferenze, statistiche e marketing cliccando su 'Va bene!' (show all). Il consenso può essere revocato in qualsiasi momento tramite le impostazioni dei cookie (qui)
Devi effettuare il login per poter lasciare una recensione.
IMPORTANTE: Per evitare di inserire informazioni per sentito dire, non complete o sbagliate, permettiamo di dare un giudizio delle attrezzature solo ai nostri clienti che hanno comprato la merce direttamente da noi.
Dopo il Login trovi nella tua area cliente troverete sotto la sezione "Giudica i prodotti" tutti gli articoli ai quali potrete dare un giudizio
Infelice acquisto.
Molto bello da vedere ma per installarlo su una strato (teoricamente sarebbe la sua collocazione naturale) bisogna intervenire pesantemente sullo scasso del capotasto con un intervento difficilmente reversibile. Oltre alla curvatura non perfettamente corretta, le sei sellette regolabili hanno bisogno di ulteriori scassi sul manico per scendere di corsa, altrimenti le corde le ritrovi a 4 mm dalla tastiera.
E fosse solo questo: gli angoli non sono particolarmente sagomati e se non si sta attenti tagliano le mani.
Aperto e rimesso in scatola, peccato perché è bello.
Qualità
0
0
Segnala un abuso
Segnala un abuso
M
Ottima fattura e molto pratico!
MarcoTaba 23.03.2018
Ottima fattura in ottone e molto pratico per regolare l'altezza al capotasto di ogni singola corda, consigliatissimo.
Sfortunatamente si è verificato un errore, La preghiamo di riprovare più tardi.
S
So far so good...
SamD 07.01.2015
I've had to modify the end of the neck to make this item fit (plus mark up and drill 6 holes) to accommodate the individual screws as they go down. The whole point about this item is to be able to install it with enough adjustment room to start low enough and then go lower. I can't see any way of using it therefore without doing the modifications above. This is ok for me (I do guitar set ups and put this on te neck of a guitar I'm building) but will be beyond the average player.
On top of that I'm looking for such a low action at the 1st fret (0.3mm typically) that it is almost impossible to install this in such a way as to ensure that height ends up half way on the screw setting (to allow for some up and some down). Right now I am just hoping I've installed it low enough - but I'm only going to find out when I finished the guitar body and installed the neck onto it. Still - I'm hopeful.
But the point here is that IF it doesn't work out for me then the above modification means an unusable neck (due to having to cut an extra step into the fingerboard surface to get this item low enough above the fretboard.
So I can't exactly recommend at this point and will come back and update - but despite all the above I'm happy to be trying it out as it *may* be an interesting solution to a MAJOR set up/intonation problem found on nearly all guitars :-)
UPDATE: I came back to the neck I'd installed this nut on a year later only to realise I'd put it in back to front. Duh. But even when I turned it round the right way I could see that when fitted it STILL wouldn't give me the low 1st fret action I require on my guitars. Since the low 1st fret action is one of the most important parts of my setups I couldn't see the point of installing something that gave me less control than before so I shelved it and reverted to a workable bone nut instead.