Al contenuto della pagina

Set of Machine Heads for Electric Bass

  • Configuration: 4 left
  • Type: open
  • Gear ratio: 1:20
  • Shaft length: 21 mm
  • Bore: 17.5 mm
  • Mounting: screws and bushings
  • Schaller no: 10250401.26.71
  • Finish: Black, chrome-plated
  • Including fixing screws and counter bearing
  • Made in Germany
  • In catalogo dal Dicembre 2008
  • Numero di articolo 221600
  • Unità incluse 1 Pezzo
  • colore Nero
€ 90
Tutti i prezzi incl. IVA
Disponibile
Disponibile

Questo prodotto è disponibile e può essere spedito immediatamente.

Informazioni sulla spedizione
1

66 Valutazioni dei clienti

4.9 / 5

Devi effettuare il login per poter lasciare una recensione.

IMPORTANTE: Per evitare di inserire informazioni per sentito dire, non complete o sbagliate, permettiamo di dare un giudizio delle attrezzature solo ai nostri clienti che hanno comprato la merce direttamente da noi.

Dopo il Login trovi nella tua area cliente troverete sotto la sezione "Giudica i prodotti" tutti gli articoli ai quali potrete dare un giudizio

Qualità

39 Recensioni

S
Molto resistenti e precisi
Scidov 05.05.2025
Prodotto di ottima qualità, resistenti e precisi.
Arrivano in una bella scatola curata, lubrificati e pronti per essere montati sul basso.
Fate attenzione alla compatibilità con il vostro strumento, non sono di semplicissima installazione.
L'unica pecca che mi sento di segnalare è che sono leggermente pesanti.
Qualità
0
0
Segnala un abuso

Segnala un abuso

google translate gb
Sfortunatamente si è verificato un errore, La preghiamo di riprovare più tardi.
t
Precise and stable
taddeomaiden 21.10.2017
The machine heads are extremely solid and allow precise tuning and stability.
Esthetically flawless and elegant as any black hardware, the installation is easy, IF you have corresponding holes, otherwise you might have some difficulties, as I had, because the mounting rings are slightly smaller than the most common ones.
The machine heads are similar to the newest ones used on Fender basses, although they don't have the typical trapezoidal plate but a smaller one.
Qualità
1
0
Segnala un abuso

Segnala un abuso

google translate gb
Sfortunatamente si è verificato un errore, La preghiamo di riprovare più tardi.
r
great quality
remork 30.11.2020
used for experimental long string instrument, to put tension on +2m piano wire. did the job just fine. had to (over)tighten the screw because of higher tension than usual (and unorthodox break angle), which put too much tension on the plastic washer inside, but once installed properly they held out without further complaints. that said, if you're using them for what they were are for, instead of the abuse i put them through, i'm sure they will also satisfy :)
Qualità
0
0
Segnala un abuso

Segnala un abuso

google translate gb
Sfortunatamente si è verificato un errore, La preghiamo di riprovare più tardi.
P
All good
Plywoo 19.11.2021
I used these to replace the revoltingly bad tuners on my Sterling Ray 35, and they are pretty much flawless so far. For info, I had to drill new holes on the bass head but that's unavoidable, at least for black tuners.

I haven't seen any issue with these, they seem solid, keep the tune perfectly and are easy to adjust. Simple and flawless as a good hammer.
Qualità
0
0
Segnala un abuso

Segnala un abuso